How to Use a Beard Trimmer

How to Use a Beard Trimmer? Every Man’s Grooming Guide

Spread the love

While they probably are a must-have tool for every bearded man, learning how to use a beard trimmer is not as simple as you probably think. Yes, they are portable and lightweight, but maneuvering it to achieve the style you want is not that simple.

Each part of a beard trimmer has an important function. The sharp set of blades promote even, detailed trimming, and the ergonomic handle supports maneuverability and comfort. Understanding how each part works will give you more power and control over your beard.

How to Use a Beard Trimmer 2

How to Use a Beard Trimmer? A Step-by-Step Guide

So, how does one use a beard trimmer properly? If you’re new to this tool, then using it may be difficult at first, as with anything new. Lucky for you, we have here an easy-to-understand guide to help you master your beard trimmer.

Step 1: Get a beard trimmer

Obviously, you need your own beard trimmer—a high-quality one, to be specific. These kinds of beard trimmers provide an even shave and allow detailed trims for a well-groomed, stylish beard. High-quality models are much more comfortable to use than low-quality ones. They do not pull out hair, which causes skin irritation and bleeding.

If you are not sure which one would best suit your needs, stick to the trusted brands. If you are not limited within a budget, choose an expensive beard trimmer with unmatched quality and features.

Step 2: Wash your beard and dry thoroughly

Dirt and dead skin cells trapped in the beard cause knots, which lead to a nasty trimming experience. Wash them out with the use of a beard shampoo. Trimming your beard while it’s wet is inconvenient and might cause hair pulling and skin irritation, which is why it is important to dry it thoroughly with a clean towel before shaving.

A clean, dry beard is much easier to trim. Without beard knots and dirt, the beard trimmer can easily navigate through your face. Especially for thicker, longer beards, ensuring that the hair points flat results in a smooth trimming experience.

Step 3: Begin with the neck area

After washing and drying up your beard, you are now ready to turn on the trimmer. Before doing so, set it to the longest length setting. Use it with caution as you don’t want to shave too much and wait for another few weeks for the beard to grow back.

Adjust the trimmer to a shorter length setting only when needed to achieve a shorter style. Once the trimmer is on, start with the neck area because this is where the hair usually grows downward. Get rid of the height adjustment attachment, so you can shave a clean, neat neckline.

When trimming the neck area, it is easy to get carried away. When you let yourself get carried away, you will take too much hair off, which you wouldn’t want to happen. To prevent this from happening, trim little by little. Regularly step back to check if you are on the right track.

Step 4: Determine a clear line on the cheeks

After shaving the neck area, the second most important part to work on is the sides of your face or your cheek line. This area helps frame your face and defines the general style you want to create.

At this point, you decide either you want to trim it to a little lower cheek line or to a full beard that reaches up to the upper part of your cheeks. For a well-defined cheek line, set the height adjustment tool aside and trim downwards. Slowly remove the parts of the beard.

While the hair on the neckline grows easily, the hair on the cheeks doesn’t. So, make sure that trim it with caution to prevent disaster. Take a step back and check if the beard has the same length on each side of the cheeks. Take note that the key to a perfectly groomed beard is symmetry.

Step 5: Set the hair length on the cheek area

A full beard can look great, but a well-defined set of hair length on the cheeks create a neat and better look. Once you have determined the length you want, you can maintain various lengths for the other cheek hair to best match your desired style and contour.

A two-millimeter length difference between the cheek hair and jawline creates a significant effect on the overall style of the beard.

Step 6: Trim the chin area

There are quite a few beard styles that you can choose from to emphasize the different areas of your face. The chin area can be trimmed in various ways, and it is just a matter of personal preference. Some men like to trim the chin area at a little bit longer length than the neck, cheek, and jaw hair.

After trimming the chin area, comb the beard to remove any loose hair. With a good-quality beard comb, you can achieve a neat beard style.

Step 7: Groom your mustache

The mustache is often underestimated when styling the beard. It is worth noting, though, that it can add life to your preferred style. Although minor errors and patches can be masked in your beard, you should still pay extra care when trimming your mustache.

Wondering how to groom your mustache? First, comb it downwards and detangle the hair over your lips with the use of a beard trimmer. For a tidier look, the mustache should be set at a longer length to keep it flat on the face. Nobody wants a prickly mustache, especially a love interest.

How to Use a Beard Trimmer 3

Conclusion

Trimming your beard into a neat, well-contoured style is not easy, and the same is true when it comes to learning the steps on how to use a beard trimmer. Once you have achieved the style you want, you can easily maintain it at different lengths. Keep it neat and well-contoured as the beard represents a part of your personality and overall appearance.

What you have to remember is that the key to a perfectly groomed beard is to use the beard trimmer with caution. Make use of the accessories that come with it, such as the height adjustment tool and beard comb.

More than that, you might also want to make sure that you regularly wash your beard with the appropriate shampoo to eliminate trapped dead skin cells. In this way, you can be sure that it grows healthily and beautifully.